HOMEOWNER TROUBLESHOOTING GUIDE

Furnace Leaking Water? What to Do Right Now and When to Call

Furnace leaking water in Indiana or Westmoreland County, PA? Find the source, stop the damage safely, spot a frozen condensate line and know when to call.

Call Now for Repair Help(724) 300-2927

Referral service. Calls may be recorded and may be routed to an independent local service provider.

Homeowner education · Public references listed below · Read our editorial standards

Water on the floor by the furnace and the house getting cold? Call to be connected with a local furnace repair pro.

Referral service. Calls may be recorded and may be routed to an independent local service provider.

QUICK ANSWER

Where to start

If your furnace is leaking water, first keep yourself safe: if water is near the furnace controls, wiring or an outlet, turn the furnace off at the thermostat and its service switch or breaker without standing in the water, and if you smell gas or a carbon monoxide alarm sounds, leave and call 911 or your gas utility from outside. Then contain the water with towels or a wet-dry vac. On a high-efficiency furnace (white PVC exhaust pipes), Carrier, Trane and Lennox say most leaks come from a clogged condensate drain or trap, a failed condensate pump or a leaking humidifier. In a Western PA winter, a condensate line that runs through a cold garage, crawlspace or outside wall can also freeze and back water up. If the leak is not an obvious loose hose, or the furnace shuts down, call a heating technician.

Key points

  • Safety first: never stand in water to reach a furnace switch, and leave the house and call 911 or the gas utility if you smell gas or a CO alarm sounds.
  • Only high-efficiency (condensing) furnaces make water. Trane says white PVC exhaust and intake pipes mean a condensing furnace; a metal flue means a standard furnace that should not make water.
  • The usual causes, per Carrier, Trane and Lennox: a clogged condensate drain or trap, a failed or unplugged condensate pump, a loose or cracked line, a leaking humidifier or an overflowing AC coil pan.
  • Winter twist: Lennox says condensate lines should run inside heated space to avoid freezing. A frozen line backs water into the furnace and can shut it down on the coldest night.
  • HomeGuide lists fixing a leaking furnace at $100 to $400 on average. Carrier says a heat exchanger problem behind a leak is a carbon monoxide concern that needs a technician right away.

Match where the water is to the safe next step

These observations help describe the issue, not diagnose it. Stop if conditions become unsafe.

What you seeSafe next step
Puddle under a high-efficiency (PVC-vented) furnace while the heat runsTurn the furnace off, contain the water and check the drain tubing, trap and condensate pump for a loose hose, kink or full tank, then call.
Furnace stopped on a very cold night and the drain runs through a garage, crawlspace or outside wallThe condensate line may be frozen. Keep the furnace off, never thaw PVC with a flame, protect your pipes and call a heating technician.
Water dripping from the humidifier on the ductworkClose the humidifier's small water supply valve, dry the area and have the pad, drain line and connections checked.
Water on the control board, inside the cabinet, or rust and corrosionShut the furnace off without standing in water and call now; a heat exchanger problem can be a carbon monoxide risk.

First, is it an emergency?

A puddle next to the furnace is usually a drain problem, not a disaster. But in Indiana County and Westmoreland County basements, where the furnace often sits beside the water heater, washer and electrical panel, a few situations need you to stop and call right away.

Leave the house and call 911 or your gas utility from outside if you smell gas (a rotten-egg smell) or a carbon monoxide alarm is sounding. Do not touch light switches or the furnace on the way out.

Turn the furnace off and call a technician if water is dripping onto the control board, wiring or an outlet, if the water is spreading toward the electrical panel, or if you see rust, corrosion or water inside the furnace cabinet. Carrier says water around electrical parts can create an electrical hazard, and that a leak tied to a damaged heat exchanger can let combustion gases, including carbon monoxide, into the air. Lennox also says not to try to fix a leaking furnace yourself because of the risk of shock.

If you have to stand in water to reach the furnace switch or a breaker, do not. Turn the furnace off at the thermostat instead, or wait for help.

Is it really the furnace? Find the source

Trane points out that if a water heater, washing machine or laundry tub sits in the same room, the water may not be coming from the furnace at all. Follow the wet trail back to where it starts. Water at the base of the water heater, the washer drain hose or a dripping supply line is a plumbing problem, not a furnace problem.

Next, check what kind of furnace you have. Trane's rule: if the exhaust pipe is metal, it is a standard furnace; if it is white PVC plastic paired with a PVC intake pipe, it is a high-efficiency condensing furnace. Lennox adds that the yellow EnergyGuide label shows the AFUE rating: about 80% means a conventional furnace, 90% or more means a condensing one.

That matters because only a condensing furnace makes water. Lennox says a conventional furnace does not produce water, so a leak at an 80% furnace usually points to a humidifier, the air conditioner coil sitting on top of it, or plumbing nearby. Many older homes in Greensburg, Latrobe, Jeannette and Indiana still have metal-flue furnaces vented into a chimney, while newer or replaced systems are more likely to be condensing units.

Finally, notice when it leaks. Water while the heat is running points to the condensate system or a humidifier. Trane says water while the AC is running in summer comes from the indoor evaporator coil and its drain pan, not the furnace.

What to do right now, step by step

1. Turn the system off. Carrier and Trane both say to turn the furnace off at the thermostat or its breaker if water is reaching electrical parts or you cannot tell where it is coming from. Most furnaces also have a service switch that looks like a light switch on or near the unit.

2. Contain the water. Put a pan or bucket under the drip and use towels, a mop or a wet-dry vac on the floor. Move boxes, rugs and anything stored on the basement floor away from the furnace.

3. Look, do not open. With the furnace off, look at the white plastic drain tubing and the trap (a U-shaped or boxy plastic fitting low on the furnace). Check for a hose that has slipped off a fitting, a kink, or a visible crack. Carrier's checklist says to look for standing water but not to take apart internal components, and never bypass or jumper a condensate safety switch.

4. Check the condensate pump, if you have one. It is a small box with a tank, usually on the floor next to the furnace, with a thin tube running to a drain or sink. Make sure it is plugged in and the outlet works. A tank full to the brim with a pump that does not run means the pump has failed or lost power.

5. Follow the drain line to its end. If the line runs to a floor drain, laundry standpipe or utility sink, make sure the end is not blocked. If it runs through a garage, crawlspace or out through an outside wall, it may be frozen (see the winter section below).

6. Check the humidifier. If a whole-house humidifier is mounted on the ductwork, Trane says a clogged pad, a cracked drain line or loose connections can leak. Close the small water valve that feeds it and see if the dripping stops.

7. Write down what you see and call. Note where the water starts, whether the furnace is running or shut down, any flashing light code on the furnace's control board window and the model number on the label. A technician can then come prepared.

Water on the floor by the furnace and the house getting cold? Call to be connected with a local furnace repair pro.

Referral service. Calls may be recorded and may be routed to an independent local service provider.

Common reasons a furnace leaks water

Clogged condensate drain or trap: Lennox says dirt and debris in the drain hose, drain line or condensate trap is one of the most common causes. When the trap clogs, water backs up inside the furnace and spills out.

Failed or unplugged condensate pump: Carrier names a condensate pump or drainage problem as a common cause. Lennox says a condensate pump typically lasts three to five years.

Loose, cracked or disconnected line: Lennox notes a line may simply have come loose, while cracked pipes and broken pumps must be replaced.

Humidifier leak: a clogged pad, a cracked drain line or a loose water connection on a furnace-mounted humidifier, according to Trane.

AC coil pan or a frozen coil: Trane and Lennox say the air conditioner's indoor coil drains into a pan that can clog and overflow, and a dirty filter can let the coil freeze, then drip as it melts.

Heat exchanger problem: less common but serious. Lennox says a faulty secondary heat exchanger can cause a condensation leak, and Carrier says a cracked heat exchanger can let carbon monoxide into the airflow. Do not inspect or repair a heat exchanger yourself.

Why furnaces leak in a Western PA winter: frozen condensate lines

A condensing furnace makes a lot of water when it runs hard. Carrier estimates that a 60,000 BTU/h furnace at full input can produce roughly 0.7 gallons of water vapor per hour from combustion, and Carrier says furnaces leak more in winter because they run more often and produce more condensation.

That water has to stay liquid all the way to the drain. Lennox's installation instructions say the condensate drain line should be routed inside the conditioned (heated) space to avoid freezing and blocking the line, and that a heat cable kit may be used where that is not possible. In homes around Blairsville, Homer City, Ligonier and Mt Pleasant, furnaces sometimes sit in a garage, crawlspace or a converted porch, or the drain is run out through the wall to the yard. On a single-digit night, those lines can freeze.

When the line freezes, the furnace acts as if the drain were clogged: water fills the trap and the collector box, then leaks out or trips a safety switch, and the heat goes off. Do not thaw PVC with a torch, heat gun or boiling water, and do not remove the trap or jumper a switch to get heat back. Turn the furnace off, keep the house from getting too cold, and call a technician to clear the line and protect or reroute it.

Protect your floors and prevent mold

Trane recommends mopping up promptly and using a fan to dry the area, because the longer water stands, the higher the risk of mold. The EPA advises drying water-damaged areas and items within 24 to 48 hours to prevent mold growth.

If the water soaked carpet, drywall or stored boxes, take photos before you move anything for your records or an insurance claim. If you rent in Indiana, Greensburg or Jeannette, tell your landlord or property manager in writing and send the photos.

While the furnace is off, keep pipes from freezing: open sink cabinets on outside walls and use only indoor-rated electric space heaters plugged straight into a wall outlet. Never heat the house with a gas oven, grill or generator.

What furnace leak repair can cost

There is no local price list, and this website does not set prices. As national reference points, HomeGuide lists the cost to fix a leaking furnace at $100 to $400 on average, depending on whether parts are cleaned or replaced, and says clogged condensate drain lines or pumps are the most common cause on high-efficiency furnaces. HomeGuide puts whole-house humidifier repair at $70 to $400.

Lennox says a replacement condensate pump costs about $50, with professional replacement running about $100 to $200. HomeGuide lists furnace service at $75 to $150 per hour plus parts, emergency after-hours service at $140 to $210 per hour, and heat exchanger replacement at $1,000 to $3,000. Ask for the service call and after-hours rate before the technician comes out, and get the repair price in writing first.

What the symptoms may tell you

Water pools under the furnace only while the heat is running, and the furnace has white PVC vent pipes.

The condensate pump tank is full to the top and the pump does not run, or it is unplugged.

The furnace shut off on a very cold night and the drain line runs through a garage, crawlspace or outside wall.

Water drips from the humidifier on the ductwork or its small supply tube.

There is rust, corrosion or water inside the furnace cabinet, or water is reaching the controls or wiring.

Homeowner checklist

  • Gas smell or CO alarm: get everyone out and call 911 or the gas utility from outside.
  • Turn the furnace off at the thermostat or service switch without standing in water.
  • Contain the water with a bucket, towels or a wet-dry vac and move stored items away.
  • Rule out the water heater, washer and laundry tub nearby.
  • Check the condensate pump is plugged in and the drain line is not kinked, loose or frozen.
  • Close the humidifier water valve if the drip is coming from the humidifier.
  • Write down any flashing code and the model number, then call a heating technician.

Safety first

Never stand in water to reach a furnace switch, breaker or outlet. If you smell gas or a carbon monoxide alarm sounds, leave the house and call 911 or your gas utility from outside. Do not open the furnace's internal panels, bypass or jumper a condensate or pressure safety switch, remove the condensate trap, or thaw plastic drain lines with an open flame, heat gun or boiling water. Do not run a furnace with water on its control board. While the heat is off, never heat the home with a gas oven, grill or generator.

When to involve a professional

Call a qualified heating technician when the leak is not a simple loose hose you can see, when the furnace shuts down or keeps locking out, when the condensate pump has failed, when the drain line is frozen, or when there is water or rust inside the furnace. Have the furnace model number, the flashing light code if any, where the water starts and whether the drain runs through a cold space ready. Ask how the visit is priced and what the after-hours rate is. Prices, availability and arrival times are set by the independent provider, not by this website.

Questions to ask before agreeing to work

  1. Where exactly is the water coming from (trap, drain line, pump, humidifier, AC coil pan or inside the furnace), and how did you confirm it?
  2. Is the furnace safe to run tonight, and did you check the heat exchanger and venting?
  3. If the line froze, can you reroute it inside heated space or protect it with heat cable so it does not happen again?

Frequently asked questions

Why is my furnace leaking water when the heat is on?

If you have a high-efficiency furnace with white PVC pipes, it makes water as it runs. Trane and Lennox say a leak usually means the condensate drain line or trap is clogged, the condensate pump failed or a line came loose. A humidifier on the ductwork can also leak. A standard furnace with a metal flue should not make water, so look at the humidifier, AC coil or nearby plumbing.

Is a furnace leaking water an emergency?

It can be. Carrier says to turn the furnace off if water is reaching electrical parts, and that a leak caused by a damaged heat exchanger can be a carbon monoxide risk. A small drip from a loose hose can wait for a service call, but water on the controls, water inside the cabinet, a CO alarm or no heat in freezing weather means call now.

Can a frozen condensate line shut off my furnace?

Yes. When the line freezes, water backs up into the furnace and a safety switch can stop it from running, so you may get no heat and water on the floor at the same time. Lennox says the drain line should run inside heated space to avoid freezing. Do not thaw PVC with a torch or boiling water; call a technician to clear and protect the line.

How much does it cost to fix a leaking furnace?

HomeGuide lists $100 to $400 on average to fix a leaking furnace, depending on whether parts are cleaned or replaced. Lennox says professional condensate pump replacement runs about $100 to $200. A heat exchanger problem costs far more; HomeGuide lists replacement at $1,000 to $3,000. Prices in your area are set by the provider.

Can you connect me with a furnace repair pro in Indiana, Greensburg or Latrobe?

Yes. Our referral service covers Indiana County and Westmoreland County, including Indiana, Blairsville, Homer City, Greensburg, Latrobe, Jeannette, Murrysville, Ligonier and Mt Pleasant. Calls may be recorded and may be routed to an independent local service provider, who confirms availability, timing and price with you.

Research references

Public information for additional reading, not endorsements or individualized professional advice.

Water on the floor by the furnace and the house getting cold? Call to be connected with a local furnace repair pro.

Referral service. Calls may be recorded and may be routed to an independent local service provider.

Call Now(724) 300-2927